;+----------------------------------------------------------------------+
;|									|
;|		JH1RSV 's G8BPQ Version 4.05 CONFIG TEXT		|
;|			for [SMC/DynaTNC] Rel.2.0			|
;|									|
;+----------------------------------------------------------------------+

HOSTINTERRUPT=127		; Sets the Interrupt BPQ Host Mode
EMS=0				; Do'nt use EMS Memory
DESQVIEW=0
NODECALL=NOCALL			; NODE CALLSIGN
NODEALIAS=NOCALL		; NODE ALIAS
BBSCALL=NOCALL		 	; BBS CALLSIGN 
BBSALIAS=NOCALL			; BBS ALIAS

IDMSG:
Network node (NOCALL)
***

UNPROTO=CQ			; DEFAULT UNPROTO ADDR

INFOMSG:
SMC/DynaTNC with G8BPQ Packet Switch.
Commands are basically the same as NET/ROM, but to connect to another
normal station (not another node), you must specify a port number before
the callsign. Use PORTS command to list available ports. The BBS command
connects you to the associated Mailbox.

         This Node have only amateur radio packet messages.
 (S-JIS) 本ノードはアマチュア無線パケット通信以外のメッセージは扱いません。

***

CTEXT:
Welcome to NOCALL's Packet Switch by SMC/DynaTNC
Type ? for list of available commands.
This Node have only amateur radio packet messages.
Type I for display of this information.
***

FULL_CTEXT=0			; SEND CTEXT ONLY TO L2 CONNECTEES TO ALIAS
OBSINIT=5			; INITIAL OBSOLESCENCE VALUE
OBSMIN=4			; MINIMUM TO BROADCAST
NODESINTERVAL=60                ; 'NODES' INTERVAL IN MINS
IDINTERVAL=15			; 'ID' BROADCAST INTERVAL (UK Regs require
				; an AX25 ID every 15 mins)
BTINTERVAL=30                   ; NO BEACONS
L3TIMETOLIVE=25			; MAX L3 HOPS
L4RETRIES=3			; LEVEL 4 RETRY COUNT
L4TIMEOUT=120			; LEVEL 4 TIMEOUT
L4DELAY=10			; LEVEL 4 DELAYED ACK TIMER
L4WINDOW=4			; DEFAULT LEVEL 4 WINDOW
MAXLINKS=30			; MAX LEVEL 2 LINKS (UP,DOWN AND INTERNODE)
MAXNODES=120			; MAX NODES IN SYSTEM
MAXROUTES=35			; MAX ADJACENT NODES
MAXCIRCUITS=64			; NUMBER OF L4 CIRCUITS
MINQUAL=10                      ; MINIMUM QUALITY TO ADD TO NODES TABLE
BBSQUAL=250                     ; BBS Quality relative to NODE - used to
				; limit 'spread' of BBS through the network
				; to your required service area. I've been
				; asked to set a low default to encourage you
				; to think about a suitable value. Max is 255
BUFFERS=255			; PACKET BUFFERS - 255 MEANS ALLOCATE AS MANY
				; AS POSSIBLE - NORMALLY ABOUT 130, DEPENDING
				; ON OTHER TABLE SIZES

PACLEN=120                      ; MAX PACKET SIZE
TRANSDELAY=1			; TRANSPARENT MODE SEND DELAY - 1 SEC

T3=180				; LINK VALIDATION TIMER (3 MINS)
IDLETIME=900                    ; IDLE LINK SHUTDOWN TIMER (10 MINS)

BBS=0				; INCLUDE BBS SUPPORT
NODE=0				; INCLUDE SWITCH SUPPORT
HIDENODES=0                     ; IF SET TO 1, NODES STARTING WITH # WILL
				; ONLY BE DISPLAYED BY A NODES * COMMAND
ENABLE_LINKED=N			; CONTROLS PROCESSING OF *** LINKED COMMAND
				; Y ALLOWS UNRESTRICTED USE
				; A ALLOWS USE BY APPLICATION PROGRAM
				; N (OR ANY OTHER VALUE) DISABLE

TNCPORT
	COM=1
ENDPORT

TNCPORT
 	COM=2
ENDPORT

TNCPORT
 	COM=3
ENDPORT

TNCPORT
	COM=4
ENDPORT

;TNCPORT
;	COM=5
;ENDPORT

;TNCPORT
;	COM=6
;ENDPORT

;TNCPORT
;	COM=7
;ENDPORT

;TNCPORT
;	COM=8
;	APPLMASK=8		; MH
;ENDPORT

;TNCPORT
;	COM=9
;	APPLMASK=16		; HELP
;ENDPORT

;TNCPORT
;	COM=10
;	APPLMASK=4		; SYSOP
;	APPLFLAGS=4
;ENDPORT

;TNCPORT
;	COM=11
;	TYPE=KISS
;	KISSMASK=1		; PORT 1 (1B)
;ENDPORT

;TNCPORT
;	COM=12
;	TYPE=KISS
;	KISSMASK=2		; PORT 2 (10B)
;ENDPORT

PORT
	ID=***.**MHz DynaTNC CH-A
	TYPE=DRSI
	PROTOCOL=HDLC
	IOADDR=2F8H
	INTLEVEL=3
	SPEED=1200
	CHANNEL=A
	QUALITY=10
	MAXFRAME=4
	TXDELAY=500
	SLOTTIME=100
	PERSIST=64
	FULLDUP=0
	SOFTDCD=1
	FRACK=7000
	RESPTIME=2000
	RETRIES=10
	PACLEN=120
;	CWID=NOCALL

ENDPORT
;
;PORT
;	ID=***.**MHz DynaTNC CH-B
;	TYPE=DRSI
;	PROTOCOL=HDLC
;	IOADDR=2F8H
;	INTLEVEL=3
;	SPEED=9600
;	CHANNEL=B
;	QUALITY=250
;	MAXFRAME=7
;	TXDELAY=500
;	SLOTTIME=100
;	PERSIST=64
;	FULLDUP=0
;	SOFTDCD=0
;	FRACK=6000
;	RESPTIME=1500
;	RETRIES=10
;	PACLEN=240
;	CWID=NOCALL
;
;ENDPORT

ROUTES:
***

APPLICATIONS=,,,,