Internet Engineering Task Force (IETF)                  D. Papadimitriou
Request for Comments: 5787                                Alcatel-Lucent
Category: Experimental                                        March 2010
ISSN: 2070-1721


                OSPFv2 Routing Protocols Extensions for
         Automatically Switched Optical Network (ASON) Routing

Abstract

   The ITU-T has defined an architecture and requirements for operating
   an Automatically Switched Optical Network (ASON).

   The Generalized Multiprotocol Label Switching (GMPLS) protocol suite
   is designed to provide a control plane for a range of network
   technologies including optical networks such as time division
   multiplexing (TDM) networks including SONET/SDH and Optical Transport
   Networks (OTNs), and lambda switching optical networks.

   The requirements for GMPLS routing to satisfy the requirements of
   ASON routing, and an evaluation of existing GMPLS routing protocols
   are provided in other documents.  This document defines extensions to
   the OSPFv2 Link State Routing Protocol to meet the requirements for
   routing in an ASON.

   Note that this work is scoped to the requirements and evaluation
   expressed in RFC 4258 and RFC 4652 and the ITU-T Recommendations
   current when those documents were written.  Future extensions of
   revisions of this work may be necessary if the ITU-T Recommendations
   are revised or if new requirements are introduced into a revision of
   RFC 4258.

Status of This Memo

   This document is not an Internet Standards Track specification; it is
   published for examination, experimental implementation, and
   evaluation.

   This document defines an Experimental Protocol for the Internet
   community.  This document is a product of the Internet Engineering
   Task Force (IETF).  It represents the consensus of the IETF
   community.  It has received public review and has been approved for
   publication by the Internet Engineering Steering Group (IESG).  Not
   all documents approved by the IESG are a candidate for any level of
   Internet Standard; see Section 2 of RFC 5741.





Papdimitriou                  Experimental                      [Page 1]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc5787.

Copyright Notice

   Copyright (c) 2010 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

































Papdimitriou                  Experimental                      [Page 2]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


Table of Contents

   1. Introduction ....................................................4
      1.1. Conventions Used in This Document ..........................5
   2. Routing Areas, OSPF Areas, and Protocol Instances ...............5
   3. Reachability ....................................................6
      3.1. Node IPv4 Local Prefix Sub-TLV .............................6
      3.2. Node IPv6 Local Prefix Sub-TLV .............................7
   4. Link Attribute ..................................................8
      4.1. Local Adaptation ...........................................8
      4.2. Bandwidth Accounting .......................................9
   5. Routing Information Scope .......................................9
      5.1. Terminology and Identification .............................9
      5.2. Link Advertisement (Local and Remote TE Router ID
           Sub-TLV) ..................................................10
      5.3. Reachability Advertisement (Local TE Router ID sub-TLV) ...11
   6. Routing Information Dissemination ..............................12
      6.1. Import/Export Rules .......................................13
      6.2. Discovery and Selection ...................................13
           6.2.1. Upward Discovery and Selection .....................13
           6.2.2. Downward Discovery and Selection ...................14
           6.2.3. Router Information Experimental Capabilities TLV ...16
      6.3. Loop Prevention ...........................................16
           6.3.1. Associated RA ID ...................................17
           6.3.2. Processing .........................................18
      6.4. Resiliency ................................................19
      6.5. Neighbor Relationship and Routing Adjacency ...............20
      6.6. Reconfiguration ...........................................20
   7. OSPFv2 Scalability .............................................21
   8. Security Considerations ........................................21
   9. Experimental Code Points .......................................21
      9.1. Sub-TLVs of the Link TLV ..................................22
      9.2. Sub-TLVs of the Node Attribute TLV ........................22
      9.3. Sub-TLVs of the Router Address TLV ........................23
      9.4. TLVs of the Router Information LSA ........................23
   10. References ....................................................24
      10.1. Normative References .....................................24
      10.2. Informative References ...................................25
   11. Acknowledgements ..............................................26
   Appendix A. ASON Terminology ......................................27
   Appendix B. ASON Routing Terminology ..............................28










Papdimitriou                  Experimental                      [Page 3]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


1.  Introduction

   The Generalized Multiprotocol Label Switching (GMPLS) [RFC3945]
   protocol suite is designed to provide a control plane for a range of
   network technologies including optical networks such as time division
   multiplexing (TDM) networks including SONET/SDH and Optical Transport
   Networks (OTNs), and lambda switching optical networks.

   The ITU-T defines the architecture of the Automatically Switched
   Optical Network (ASON) in [G.8080].

   [RFC4258] details the routing requirements for the GMPLS suite of
   routing protocols to support the capabilities and functionality of
   ASON control planes identified in [G.7715] and in [G.7715.1].

   [RFC4652] evaluates the IETF Link State routing protocols against the
   requirements identified in [RFC4258].  Section 7.1 of [RFC4652]
   summarizes the capabilities to be provided by OSPFv2 [RFC2328] in
   support of ASON routing.  This document details the OSPFv2 specifics
   for ASON routing.

   Multi-layer transport networks are constructed from multiple networks
   of different technologies operating in a client-server relationship.
   The ASON routing model includes the definition of routing levels that
   provide scaling and confidentiality benefits.  In multi-level
   routing, domains called routing areas (RAs) are arranged in a
   hierarchical relationship.  Note that as described in [RFC4652] there
   is no implied relationship between multi-layer transport networks and
   multi-level routing.  The multi-level routing mechanisms described in
   this document work for both single-layer and multi-layer networks.

   Implementations may support a hierarchical routing topology (multi-
   level) for multiple transport network layers and/or a hierarchical
   routing topology for a single transport network layer.

   This document details the processing of the generic (technology-
   independent) link attributes that are defined in [RFC3630],
   [RFC4202], and [RFC4203] and that are extended in this document.  As
   detailed in Section 4.2, technology-specific traffic engineering
   attributes (and their processing) may be defined in other documents
   that complement this document.

   Note that this work is scoped to the requirements and evaluation
   expressed in [RFC4258] and [RFC4652] and the ITU-T Recommendations
   current when those documents were written.  Future extensions of
   revisions of this work may be necessary if the ITU-T Recommendations
   are revised or if new requirements are introduced into a revision of
   [RFC4258].



Papdimitriou                  Experimental                      [Page 4]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   This document is classified as Experimental.  Significant changes to
   routing protocols are of concern to the stability of the Internet.
   The extensions described in this document are intended for cautious
   use in self-contained environments.  The objective is to determine
   whether these extensions are stable and functional, whether there is
   a demand for implementation and deployment, and whether the
   extensions have any impact on existing routing protocol deployments.

1.1.  Conventions Used in This Document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED",  "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

   The reader is assumed to be familiar with the terminology and
   requirements developed in [RFC4258] and the evaluation outcomes
   detailed in [RFC4652].

   General ASON terminology is provided in Appendix A.  ASON routing
   terminology is described in Appendix B.

2.  Routing Areas, OSPF Areas, and Protocol Instances

   An ASON routing area (RA) represents a partition of the data plane,
   and its identifier is used within the control plane as the
   representation of this partition.

   RAs are arranged in hierarchical levels such that any one RA may
   contain multiple other RAs, and is wholly contained by a single RA.
   Thus, an RA may contain smaller RAs inter-connected by links.  The
   limit of the subdivision results in an RA that contains just two sub-
   networks interconnected by a single link.

   An ASON RA can be mapped to an OSPF area, but the hierarchy of ASON
   RA levels does not map to the hierarchy of OSPF routing areas.
   Instead, successive hierarchical levels of RAs MUST be represented by
   separate instances of the protocol.  Thus, inter-level routing
   information exchange (as described in Section 6) involves the export
   and import of routing information between protocol instances.

   An ASON RA may therefore be identified by the combination of its OSPF
   instance identifier and its OSPF area identifier.  With proper and
   careful network-wide configuration, this can be achieved using just
   the OSPF area identifier, and this process is RECOMMENDED in this
   document.  These concepts and the subsequent handling of network
   reconfiguration is discussed in Section 6.





Papdimitriou                  Experimental                      [Page 5]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


3.  Reachability

   In order to advertise blocks of reachable address prefixes, a
   summarization mechanism is introduced that complements the techniques
   described in [RFC5786].

   This extension takes the form of a network mask (a 32-bit number
   indicating the range of IP addresses residing on a single IP
   network/subnet).  The set of local addresses is carried in an OSPFv2
   TE LSA Node Attribute TLV (a specific sub-TLV is defined per address
   family, i.e., IPv4 and IPv6, used as network-unique identifiers).

   The proposed solution is to advertise the local address prefixes of a
   router as new sub-TLVs of the (OSPFv2 TE LSA) Node Attribute top-
   level TLV.  This document defines the following sub-TLVs:

      - Node IPv4 Local Prefix sub-TLV: Length: variable
      - Node IPv6 Local Prefix sub-TLV: Length: variable

3.1.  Node IPv4 Local Prefix Sub-TLV

   The Type field of the Node IPv4 Local Prefix sub-TLV is assigned a
   value in the range 32768-32777 agreed to by all participants in the
   experiment.  The Value field of this sub-TLV contains one or more
   local IPv4 prefixes.  The Length is measured in bytes and, as defined
   in [RFC3630], reports the length in bytes of the Value part of the
   sub-TLV.  It is set to 8 x n, where n is the number of local IPv4
   prefixes included in the sub-TLV.

   The Node IPv4 Local Prefix sub-TLV has the following format:

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |              Type             |         Length (8 x n)        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                         Network Mask 1                        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                         IPv4 Address 1                        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                                                               |
    //                             ...                              //
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                         Network Mask n                        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                         IPv4 Address n                        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+



Papdimitriou                  Experimental                      [Page 6]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   Network mask i: A 32-bit number indicating the IPv4 address mask for
   the ith advertised destination prefix.

   Each <Network mask, IPv4 Address> pair listed as part of this sub-TLV
   represents a reachable destination prefix hosted by the advertising
   Router ID.

   The local addresses that can be learned from Opaque TE LSAs (that is,
   the router address and TE interface addresses) SHOULD NOT be
   advertised in the node IPv4 Local Prefix sub-TLV.

3.2.  Node IPv6 Local Prefix Sub-TLV

   The Type field of the Node IPv6 Local Prefix sub-TLV is assigned a
   value in the range 32768-32777 agreed to by all participants in the
   experiment.  The Value field of this sub-TLV contains one or more
   local IPv6 prefixes.  IPv6 Prefix representation uses [RFC5340],
   Section A.4.1.

   The Node IPv6 Local Prefix sub-TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |              Type             |            Length             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | PrefixLength  | PrefixOptions |             (0)               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   |                     IPv6 Address Prefix 1                     |
   |                                                               |
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   //                             ...                              //
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | PrefixLength  | PrefixOptions |             (0)               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   |                     IPv6 Address Prefix n                     |
   |                                                               |
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+







Papdimitriou                  Experimental                      [Page 7]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   Length reports the length of the Value part of the sub-TLV in bytes.
   It is set to the sum over all of the local prefixes included in the
   sub-TLV of (4 + (number of 32-bit words in the prefix) * 4).

   The encoding of each prefix potentially using fewer than four 32-bit
   words is described below.

     PrefixLength: Length in bits of the prefix.

     PrefixOptions: 8-bit field describing various capabilities
       associated with the prefix (see [RFC5340], Section A.4.2).

     IPv6 Address Prefix i: The ith IPv6 address prefix in the list.
       Each prefix is encoded in an even multiple of 32-bit words using
       the fewest pairs of 32-bit words necessary to include the entire
       prefix.  Thus, each prefix is encoded in either 64 or 128 bits
       with trailing zero bit padding as necessary.

   The local addresses that can be learned from TE LSAs, i.e., router
   address and TE interface addresses, SHOULD NOT be advertised in the
   node IPv6 Local Prefix sub-TLV.

4.  Link Attribute

   [RFC4652] provides a map between link attributes and characteristics
   and their representation in sub-TLVs of the top-level Link TLV of the
   Opaque TE LSA [RFC3630] and [RFC4203], with the exception of the
   local adaptation (see below).  Advertisement of this information
   SHOULD be supported on a per-layer basis, i.e., one Opaque TE LSA per
   switching capability (and per bandwidth granularity, e.g., low-order
   virtual container and high-order virtual container).

4.1.  Local Adaptation

   Local adaptation is defined as a TE link attribute (i.e., sub-TLV)
   that describes the cross/inter-layer relationships.

   The Interface Switching Capability Descriptor (ISCD) TE Attribute
   [RFC4202] identifies the ability of the TE link to support cross-
   connection to another link within the same layer, and the ability to
   use a locally terminated connection that belongs to one layer as a
   data link for another layer (adaptation capability).  However, the
   information associated with the ability to terminate connections
   within that layer (referred to as the termination capability) is
   embedded with the adaptation capability.






Papdimitriou                  Experimental                      [Page 8]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   For instance, a link between two optical cross-connects will contain
   at least one ISCD attribute describing the lambda switching capable
   (LSC) switching capability; whereas a link between an optical cross-
   connect and an IP/MPLS LSR will contain at least two ISCD attributes:
   one for the description of the LSC termination capability and one for
   the packet switching capable (PSC) adaptation capability.

   In OSPFv2, the Interface Switching Capability Descriptor (ISCD) is a
   sub-TLV (of type 15) of the top-level Link TLV (of type 2) [RFC4203].

   The adaptation and termination capabilities are advertised using two
   separate ISCD sub-TLVs within the same top-level Link TLV.

   Per [RFC4202] and [RFC4203], an interface MAY have more than one ISCD
   sub-TLV.  Hence, the corresponding advertisements should not result
   in any compatibility issues.

   Further refinement of the ISCD sub-TLV for multi-layer networks is
   outside the scope of this document.

4.2.  Bandwidth Accounting

   GMPLS routing defines an Interface Switching Capability Descriptor
   (ISCD) that delivers, among other things, information about the
   (maximum/minimum) bandwidth per priority that a Label Switched Path
   (LSP) can make use of.  Per [RFC4202] and [RFC4203], one or more ISCD
   sub-TLVs can be associated with an interface.  This information,
   combined with the Unreserved Bandwidth (sub-TLV defined in [RFC3630],
   Section 2.5.8), provides the basis for bandwidth accounting.

   In the ASON context, additional information may be included when the
   representation and information in the other advertised fields are not
   sufficient for a specific technology (e.g., SDH).  The definition of
   technology-specific information elements is beyond the scope of this
   document.  Some technologies will not require additional information
   beyond what is already defined in [RFC3630], [RFC4202], and
   [RFC4203].

5.  Routing Information Scope

5.1.  Terminology and Identification

   The definition of short-hand terminology introduced in [RFC4652] is
   repeated here for clarity.

   - Pi is a physical (bearer/data/transport plane) node.





Papdimitriou                  Experimental                      [Page 9]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   - Li is a logical control plane entity that is associated to a single
     data plane (abstract) node.  Each Li is identified by a unique TE
     Router ID.  The latter is a control plane identifier, defined as
     the Router Address top-level TLV of the Type 1 TE LSA [RFC3630].

     Note: The Router Address top-level TLV definition, processing, and
     usage remain per [RFC3630].  This TLV specifies a stable IP address
     of the advertising router (Ri) that is always reachable if there is
     any IP connectivity to it (e.g., via the Data Communication
     Network).  Moreover, each advertising router advertises a unique,
     reachable IP address for each Pi on behalf of which it makes
     advertisements.

   - Ri is a logical control plane entity that is associated to a
     control plane "router".  The latter is the source for topology
     information that it generates and shares with other control plane
     "routers".  The Ri is identified by the (advertising) Router ID
     (32-bit) [RFC2328].

     The Router ID, which is represented by Ri and which corresponds to
     the RC-ID [RFC4258], does not enter into the identification of the
     logical entities representing the data plane resources such as
     links.  The Routing Database (RDB) is associated to the Ri.

   Note: Aside from the Li/Pi mappings, these identifiers are not
   assumed to be in a particular entity relationship except that the Ri
   may have multiple Lis in its scope.  The relationship between Ri and
   Li is simple at any moment in time: an Li may be advertised by only
   one Ri at any time.  However, an Ri may advertise a set of one or
   more Lis.  Hence, the OSPFv2 routing protocol must support a single
   Ri advertising on behalf of more than one Li.

5.2.  Link Advertisement (Local and Remote TE Router ID Sub-TLV)

   A Router ID (Ri) advertising on behalf multiple TE Router IDs (Lis)
   creates a 1:N relationship between the Router ID and the TE Router
   ID.  As the link local and link remote (unnumbered) ID association is
   not unique per node (per Li unicity), the advertisement needs to
   indicate the remote Lj value and rely on the initial discovery
   process to retrieve the [Li;Lj] relationship.  In brief, as
   unnumbered links have their ID defined on a per-Li basis, the remote
   Lj needs to be identified to scope the link remote ID to the local
   Li.  Therefore, the routing protocol MUST be able to disambiguate the
   advertised TE links so that they can be associated with the correct
   TE Router ID.






Papdimitriou                  Experimental                     [Page 10]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   For this purpose, a new sub-TLV of the (OSPFv2 TE LSA) top-level Link
   TLV is introduced that defines the Local and Remote TE Router ID.

   The Type field of the Local and Remote TE Router ID sub-TLV is
   assigned a value in the range 32768-32777 agreed to by all
   participants in the experiment.  The Length field takes the value 8.
   The Value field of this sub-TLV contains 4 octets of the Local TE
   Router Identifier followed by 4 octets of the Remote TE Router
   Identifier.  The value of the Local and Remote TE Router Identifier
   SHOULD NOT be set to 0.

   The format of the Local and Remote TE Router ID sub-TLV is:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |              Type             |          Length (8)           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                 Local TE Router Identifier                    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                 Remote TE Router Identifier                   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This sub-TLV is only required to be included as part of the top-level
   Link TLV if the Router ID is advertising on behalf of more than one
   TE Router ID.  In any other case, this sub-TLV SHOULD be omitted
   except if the operator plans to start off with 1 Li and progressively
   add more Lis (under the same Ri) such as to maintain consistency.

   Note: The Link ID sub-TLV that identifies the other end of the link
   (i.e., Router ID of the neighbor for point-to-point links) MUST
   appear exactly once per Link TLV.  This sub-TLV MUST be processed as
   defined in [RFC3630].

5.3.  Reachability Advertisement (Local TE Router ID sub-TLV)

   When the Router ID is advertised on behalf of multiple TE Router IDs
   (Lis), the routing protocol MUST be able to associate the advertised
   reachability information with the correct TE Router ID.

   For this purpose, a new sub-TLV of the (OSPFv2 TE LSA) top-level Node
   Attribute TLV is introduced.  This TLV associates the local prefixes
   (see above) to a given TE Router ID.








Papdimitriou                  Experimental                     [Page 11]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   The Type field of the Local TE Router ID sub-TLV is assigned a value
   in the range 32768-32777 agreed to by all participants in the
   experiment.  The Length field takes the value 4.  The Value field of
   this sub-TLV contains the Local TE Router Identifier [RFC3630]
   encoded over 4 octets.

   The format of the Local TE Router ID sub-TLV is:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |              Type             |          Length (4)           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                 Local TE Router Identifier                    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This sub-TLV is only required to be included as part of the Node
   Attribute TLV if the Router ID is advertising on behalf of more than
   one TE Router ID.  In any other case, this sub-TLV SHOULD be omitted.

6.  Routing Information Dissemination

   An ASON routing area (RA) represents a partition of the data plane,
   and its identifier is used within the control plane as the
   representation of this partition.  An RA may contain smaller RAs
   inter-connected by links.  The limit of the subdivision results is an
   RA that contains two sub-networks interconnected by a single link.
   ASON RA levels do not reflect routing protocol levels (such as OSPF
   areas).

   Successive hierarchical levels of RAs can be represented by separate
   instances of the protocol.

   Routing controllers (RCs) supporting RAs disseminate information
   downward and upward in this hierarchy.  The vertical routing
   information dissemination mechanisms described in this section do not
   introduce or imply a new OSPF routing area hierarchy.  RCs supporting
   RAs at multiple levels are structured as separate OSPF instances with
   routing information exchanges between levels described by import and
   export rules operating between OSPF instances.

   The implication is that an RC that performs import/export of routing
   information as described in this document does not implement an Area
   Border Router (ABR) functionality.







Papdimitriou                  Experimental                     [Page 12]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


6.1.  Import/Export Rules

   RCs supporting RAs disseminate information upward and downward in the
   hierarchy by importing/exporting routing information as Opaque TE
   LSAs (Opaque Type 1) of LS Type 10.  The information that MAY be
   exchanged between adjacent levels includes the Router Address, Link,
   and Node Attribute top-level TLVs.

   The Opaque TE LSA import/export rules are governed as follows:

   - If the export target interface is associated with the same RA as is
     associated with the import interface, the Opaque LSA MUST NOT be
     imported.

   - If a match is found between the advertising Router ID in the header
     of the received Opaque TE LSA and one of the Router IDs belonging
     to the RA of the export target interface, the Opaque LSA MUST NOT
     be imported.

   - If these two conditions are not met, the Opaque TE LSA MAY be
     imported according to local policy.  If imported, the LSA MAY be
     disseminated according to local policy.  If disseminated, the
     normal OSPF flooding rules MUST be followed and the advertising
     Router ID MUST be set to the importing router's Router ID.

   The imported/exported routing information content MAY be transformed,
   e.g., filtered or aggregated, as long as the resulting routing
   information is consistent.  In particular, when more than one RC is
   bound to adjacent levels and both are allowed to import/export
   routing information, it is expected that these transformations are
   performed in a consistent manner.  Definition of these policy-based
   mechanisms is outside the scope of this document.

   In practice, and in order to avoid scalability and processing
   overhead, routing information imported/exported downward/upward in
   the hierarchy is expected to include reachability information (see
   Section 3) and, upon strict policy control, link topology
   information.

6.2 Discovery and Selection

6.2.1.  Upward Discovery and Selection

   In order to discover RCs that are capable of disseminating routing
   information up the routing hierarchy, the following capability
   descriptor bit is set in the OSPF Router Information Experimental
   Capabilities TLV (see Section 6.2.3) carried in the Router
   Information LSA ([RFC4970]).



Papdimitriou                  Experimental                     [Page 13]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   - U bit: When set, this flag indicates that the RC is capable of
     disseminating routing information upward to the adjacent level.

   In the case that multiple RCs are advertised from the same RA with
   their U bit set, the RC with the highest Router ID, among those RCs
   with the U bit set, SHOULD be selected as the RC for upward
   dissemination of routing information.  The other RCs MUST NOT
   participate in the upward dissemination of routing information as
   long as the Opaque LSA information corresponding to the highest
   Router ID RC does not reach MaxAge.  This mechanism prevents more
   than one RC advertising routing information upward in the routing
   hierarchy from the same RA.

   Note that if the information to allow the selection of the RC that
   will be used to disseminate routing information up the hierarchy from
   a specific RA cannot be discovered automatically, it MUST be manually
   configured.

   Once an RC has been selected, it remains unmodified even if an RC
   with a higher Router ID is introduced and advertises its capability
   to disseminate routing information upward the adjacent level (i.e., U
   bit set).  This hysteresis mechanism prevents from disturbing the
   upward routing information dissemination process in case, e.g., of
   flapping.

6.2.2.  Downward Discovery and Selection

   The same discovery mechanism is used for selecting the RC responsible
   for dissemination of routing information downward in the hierarchy.
   However, an additional restriction MUST be applied such that the RC
   selection process takes into account that an upper level may be
   adjacent to one or more lower (RA) levels.  For this purpose, a
   specific TLV indexing the (lower) RA ID to which the RCs are capable
   of disseminating routing information is needed.

   The Downstream Associated RA ID TLV is carried in the OSPF Router
   Information LSA [RFC4970].  The Type field of the Downstream
   Associated RA ID TLV is assigned a value in the range 32768-32777
   agreed to by all participants in the experiment.  The Length of this
   TLV is n x 4 octets.  The Value field of this sub-TLV contains the
   list of Associated RA IDs.  Each Associated RA ID value is encoded
   following the OSPF area ID (32 bits) encoding rules defined in
   [RFC2328].








Papdimitriou                  Experimental                     [Page 14]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   The format of the Downstream Associated RA ID TLV is:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |              Type             |         Length (4 x n)        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                     Associated RA ID 1                        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   //                             ...                              //
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                     Associated RA ID n                        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   To discover RCs that are capable of disseminating routing information
   downward through the routing hierarchy, the following capability
   descriptor bit is set in the OSPF Router Information Experimental
   Capabilities TLV (see Section 6.2.3) carried in the Router
   Information LSA ([RFC4970]).

   Note that the Downstream Associated RA ID TLV MUST be present when
   the D bit is set.

   - D bit: when set, this flag indicates that the RC is capable of
     disseminating routing information downward to the adjacent levels.

   If multiple RCs are advertised for the same Associated RA ID, the RC
   with the highest Router ID, among the RCs with the D bit set, MUST be
   selected as the RC for downward dissemination of routing information.
   The other RCs for the same Associated RA ID MUST NOT participate in
   the downward dissemination of routing information as long as the
   Opaque LSA information corresponding to the highest Router ID RC does
   not reach MaxAge.  This mechanism prevents more than one RC from
   advertising routing information downward through the routing
   hierarchy.

   Note that if the information to allow the selection of the RC that
   will be used to disseminate routing information down the hierarchy to
   a specific RA cannot be discovered automatically, it MUST be manually
   configured.

   The OSPF Router information Opaque LSA (Opaque type of 4, Opaque ID
   of 0) and its content, in particular the Router Informational
   Capabilities TLV [RFC4970] and TE Node Capability Descriptor TLV
   [RFC5073], MUST NOT be re-originated.




Papdimitriou                  Experimental                     [Page 15]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


6.2.3.  Router Information Experimental Capabilities TLV

   A new TLV is defined for inclusion in the Router Information LSA to
   carry experimental capabilities because the assignment policy for
   bits in the Router Informational Capabilities TLV is "Standards
   Action" [RFC5226] prohibiting its use from Experimental documents.

   The format of the Router Information Experimental Capabilities TLV is
   as follows:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |              Type             |             Length            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |             Experimental Capabilities                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      Type     A value in the range 32768-32777 agreed to by all
               participants in the experiment.

      Length   A 16-bit field that indicates the length of the value
               portion in octets and will be a multiple of 4 octets
               dependent on the number of capabilities advertised.
               Initially, the length will be 4, denoting 4 octets of
               informational capability bits.

      Value    A variable-length sequence of capability bits rounded to
               a multiple of 4 octets padded with undefined bits.

   The following experimental capability bits are assigned:

      Bit       Capabilities

      0         The U bit (see Section 6.2.1)
      1         The D bit (see Section 6.2.2)

6.3.  Loop Prevention

   When more than one RC is bound to an adjacent level of the hierarchy,
   and is configured or selected to redistribute routing information
   upward and downward, a specific mechanism is required to avoid
   looping of routing information.  Looping is the re-introduction of
   routing information that has been advertised from the upper level
   back to the upper level.  This specific case occurs, for example,
   when the RC advertising routing information downward in the hierarchy
   is not the same one that advertises routing upward in the hierarchy.




Papdimitriou                  Experimental                     [Page 16]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   When these conditions are met, it is necessary to have a means by
   which an RC receiving an Opaque TE LSA imported/exported downward by
   an RC associated to the same RA does not import/export the content of
   this LSA back upward into the (same) upper level.

   Note that configuration and operational simplification can be
   obtained when both functionalities are configured on a single RC (per
   pair of adjacent levels) fulfilling both roles.  Figure 1 provides an
   example where such simplification applies.

              ....................................................
              .                                                  .
              .            RC_5 ------------ RC_6                .
              .             |                 |                  .
              .             |                 |            RA_Y  .
     Upper    .           *********         *********            .
     Layer    ............* RC_1a *.........* RC_2a *.............
        __________________* |     *_________* |     *__________________
              ............* RC_1b *...   ...* RC 2b *.............
     Lower    .           *********  .   .  *********            .
     Layer    .             |        .   .    |                  .
              .  RA_Z       |        .   .    |            RA_X  .
              .            RC_3      .   .   RC_4                .
              .                      .   .                       .
              ........................   .........................

               Figure 1.  Hierarchical Environment (Example)

   In this case, the procedure described in this section MAY be omitted,
   as long as these conditions are permanently guaranteed.  In all other
   cases, without exception, the procedure described in this section
   MUST be applied.

6.3.1.  Associated RA ID

   We need some way of filtering the downward/upward re-originated
   Opaque TE LSA.  Per [RFC5250], the information contained in Opaque
   LSAs may be used directly by OSPF.  By adding the RA ID associated
   with the incoming routing information, the loop prevention problem
   can be solved.

   This additional information, referred to as the Associated RA ID, MAY
   be carried in Opaque LSAs that include any of the following top-level
   TLVs:

      - Router Address top-level TLV
      - Link top-level TLV
      - Node Attribute top-level TLV



Papdimitriou                  Experimental                     [Page 17]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   The Associated RA ID reflects the identifier of the area from which
   the routing information is received.  For example, for a multi-level
   hierarchy, this identifier does not reflect the originating RA ID; it
   will reflect the RA from which the routing information is imported.

   The Type field of the Associated RA ID sub-TLV is assigned a value in
   the range 32768-32777 agreed to by all participants in the
   experiment.  The same value MUST be used for the Type regardless of
   which TLV the sub-TLV appears in.

   The Length of the Associated RA ID TLV is 4 octets.  The Value field
   of this sub-TLV contains the Associated RA ID.  The Associated RA ID
   value is encoded following the OSPF area ID (32 bits) encoding rules
   defined in [RFC2328].

   The format of the Associated RA ID TLV is defined as follows:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |              Type             |           Length (4)          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                       Associated RA ID                        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

6.3.2.  Processing

   When fulfilling the rules detailed in Section 6.1, a given Opaque LSA
   is imported/exported downward or upward the routing hierarchy, and
   the Associated RA ID TLV is added to the received Opaque LSA list of
   TLVs such as to identify the area from which this routing information
   has been received.

   When the RC adjacent to the lower or upper routing level receives
   this Opaque LSA, the following rule is applied (in addition to the
   rule governing the import/export of Opaque LSAs as detailed in
   Section 6.1).

   - If a match is found between the Associated RA ID of the received
     Opaque TE LSA and the RA ID belonging to the area of the export
     target interface, the Opaque TE LSA MUST NOT be imported.

   - Otherwise, this Opaque LSA MAY be imported and disseminated
     downward or upward the routing hierarchy following the OSPF
     flooding rules.

   This mechanism ensures that no race condition occurs when the
   conditions depicted in Figure 2 are met.



Papdimitriou                  Experimental                     [Page 18]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


                           RC_5 ------------- RC_6
                            |                 |
                            |                 |            RA_Y
     Upper                *********         *********
     Layer    ............* RC_1a *.........* RC_2a *.............
        __________________* |     *_________* |     *__________________
              ............* RC_1b *.........* RC_2b *.............
     Lower                *********         *********
     Layer                  |                 |
                            |                 |            RA_X
                           RC_3 --- . . . --- RC_4

               Figure 2.  Race Condition Prevention (Example)

   Assume that RC_1b is configured for exporting routing information
   upward toward RA_Y (upward the routing hierarchy) and that RC_2a is
   configured for exporting routing information toward RA_X (downward
   the routing hierarchy).

   Assume that routing information advertised by RC_3 would reach RC_4
   faster across RA_Y through hierarchy.

   If RC_2b is not able to prevent from importing that information, RC_4
   may receive that information before the same advertisement would
   propagate in RA_X (from RC_3) to RC_4.  For this purpose, RC_1a
   inserts the Associated RA X to the imported routing information from
   RA_X.  Because RC_2b finds a match between the Associated RA ID (X)
   of the received Opaque TE LSA and the ID (X) of the RA of the export
   target interface, this LSA MUST NOT be imported.

6.4.  Resiliency

   OSPF creates adjacencies between neighboring routers for the purpose
   of exchanging routing information.  After a neighbor has been
   discovered, bidirectional communication is ensured, and a routing
   adjacency is formed between RCs, loss of communication may result in
   partitioned OSPF areas and so in partitioned RAs.

   Consider for instance (see Figure 2) the case where RC_1a and RC_1b
   are configured for exchanging routing information downward and upward
   RA_Y, respectively, and that RC_2a and RC_2b are not configured for
   exchanging any routing information toward RA_X.  If the communication
   between RC_1a and RC_2a is broken (due, e.g., to RC_5 - RC_6
   communication failure), RA_Y could be partitioned.

   In these conditions, it is RECOMMENDED that RC_2a be re-configurable
   such as to allow for exchanging routing information downward to RA_X.
   This reconfiguration MAY be performed manually or automatically.  In



Papdimitriou                  Experimental                     [Page 19]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   the latter cases, automatic reconfiguration uses the mechanism
   described in Section 6.2 (forcing MaxAge of the corresponding opaque
   LSA information in case the originating RC becomes unreachable).
   Manual reconfiguration MUST be supported.

6.5.  Neighbor Relationship and Routing Adjacency

   It is assumed that (point-to-point) IP control channels are
   provisioned/configured between RCs belonging to the same routing
   level.  Provisioning/configuration techniques are outside the scope
   of this document.

   Once established, the OSPF Hello protocol is responsible for
   establishing and maintaining neighbor relationships.  This protocol
   also ensures that communication between neighbors is bidirectional.
   Routing adjacency can subsequently be formed between RCs following
   mechanisms defined in [RFC2328].

6.6 Reconfiguration

   This section details the RA ID reconfiguration steps.

   Reconfiguration of the RA ID occurs when the RA ID is modified, e.g.,
   from value Z to value X or Y (see Figure 2).

   The process of reconfiguring the RA ID involves:

   - Disable the import/export of routing information from the upper and
     lower levels (to prevent any LS information update).

   - Change the RA ID of the local level RA from, e.g., Z to X or Y.
     Perform a Link State Database (LSDB) checksum on all routers to
     verify that LSDBs are consistent.

   - Enable import of upstream and downstream routing information such
     as to re-synchronize local-level LSDBs from any LS information that
     may have occurred in an upper or a lower routing level.

   - Enable export of routing information downstream such as to re-sync
     the downstream level with the newly reconfigured RA ID (as part of
     the re-advertised Opaque TE LSA).

   - Enable export of routing information upstream such as to re-sync
     the upstream level with the newly reconfigured RA ID (as part of
     the re-advertised Opaque TE LSA).

   Note that the re-sync operation needs to be carried out only between
   the directly adjacent upper and lower routing levels.



Papdimitriou                  Experimental                     [Page 20]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


7.  OSPFv2 Scalability

   - Routing information exchange upward/downward in the hierarchy
     between adjacent RAs SHOULD by default be limited to reachability
     information.  In addition, several transformations such as prefix
     aggregation are RECOMMENDED when allowing the amount of information
     imported/exported by a given RC to be decreased without impacting
     consistency.

   - Routing information exchange upward/downward in the hierarchy
     involving TE attributes MUST be under strict policy control.
     Pacing and min/max thresholds for triggered updates are strongly
     RECOMMENDED.

   - The number of routing levels MUST be maintained under strict policy
     control.

8.  Security Considerations

   This document specifies the contents and processing of Opaque LSAs in
   OSPFv2 [RFC2328].  Opaque TE and RI LSAs defined in this document are
   not used for SPF computation, and so have no direct effect on IP
   routing.  Additionally, ASON routing domains are delimited by the
   usual administrative domain boundaries.

   Any mechanisms used for securing the exchange of normal OSPF LSAs can
   be applied equally to all Opaque TE and RI LSAs used in the ASON
   context.  Authentication of OSPFv2 LSA exchanges (such as OSPF
   cryptographic authentication [RFC2328] and [RFC5709]) can be used to
   secure against passive attacks and provide significant protection
   against active attacks.  [RFC5709] defines a mechanism for
   authenticating OSPF packets by making use of the HMAC algorithm in
   conjunction with the SHA family of cryptographic hash functions.

   [RFC2154] adds 1) digital signatures to authenticate OSPF LSA data,
   2) a certification mechanism for distribution of routing information,
   and 3) a neighbor-to-neighbor authentication algorithm to protect
   local OSPFv2 protocol exchanges.

9.  Experimental Code Points

   This document is classified as Experimental.  It defines new TLVs and
   sub-TLVs for inclusion in OSPF LSAs.  According to the assignment
   policies for the registries of code points for these TLVs and sub-
   TLVs, values must be assigned from the experimental ranges and must
   not be recorded by IANA or mentioned in this document.

   The following sections summarize the TLVs and sub-TLVs concerned.



Papdimitriou                  Experimental                     [Page 21]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


9.1.  Sub-TLVs of the Link TLV

   This document defines the following sub-TLVs of the Link TLV carried
   in the OSPF TE LSA:

   - Local and Remote TE Router ID sub-TLV
   - Associated RA ID sub-TLV

   The defining text for code point assignment for sub-TLVs of the OSPF
   TE Link TLV says ([RFC3630]):

      o  Types in the range 10-32767 are to be assigned via Standards
         Action.

      o  Types in the range 32768-32777 are for experimental use; these
         will not be registered with IANA, and MUST NOT be mentioned by
         RFCs.

      o  Types in the range 32778-65535 are not to be assigned at this
         time.

   That means that the new sub-TLVs must be assigned type values from
   the range 32768-32777.  It is a matter for experimental
   implementations to assign their own code points, and to agree with
   cooperating implementations participating in the same experiments
   what values to use.

   Note that the same value for the Associated RA ID sub-TLV MUST be
   used when it appears in the Link TLV, the Node Attribute TLV, and the
   Router Address TLV.

9.2.  Sub-TLVs of the Node Attribute TLV

   This document defines the following sub-TLVs of the Node Attribute
   TLV carried in the OSPF TE LSA.

      - Node IPv4 Local Prefix sub-TLV
      - Node IPv6 Local Prefix sub-TLV
      - Local TE Router ID sub-TLV
      - Associated RA ID sub-TLV

   The defining text for code point assignment for sub-TLVs of the OSPF
   Node Attribute TLV says ([RFC5786]):

      o  Types in the range 3-32767 are to be assigned via Standards
         Action.





Papdimitriou                  Experimental                     [Page 22]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


      o  Types in the range 32768-32777 are for experimental use; these
         will not be registered with IANA, and MUST NOT be mentioned by
         RFCs.

      o  Types in the range 32778-65535 are not to be assigned at this
         time.  Before any assignments can be made in this range, there
         MUST be a Standards Track RFC that specifies IANA
         Considerations that covers the range being assigned.

   That means that the new sub-TLVs must be assigned type values from
   the range 32768-32777.  It is a matter for experimental
   implementations to assign their own code points, and to agree with
   cooperating implementations participating in the same experiments
   what values to use.

   Note that the same value for the Associated RA ID sub-TLV MUST be
   used when it appears in the Link TLV, the Node Attribute TLV, and the
   Router Address TLV.

9.3.  Sub-TLVs of the Router Address TLV

   The OSPF Router Address TLV is defined in [RFC3630].  No sub-TLVs are
   defined in that document and there is no registry or allocation
   policy for sub-TLVs of the Router Address TLV.

   This document defines the following new sub-TLV for inclusion in the
   OSPF Router Address TLV:

   - Associated RA ID sub-TLV

   Note that the same value for the Associated RA ID sub-TLV MUST be
   used when it appears in the Link TLV, the Node Attribute TLV, and the
   Router Address TLV.  This is consistent with potential for a future
   definition of a registry with policies that match the other existing
   registries.

9.4.  TLVs of the Router Information LSA

   This document defines two new TLVs to be carried in the Router
   Information LSA.

      - Downstream Associated RA ID TLV
      - Router Information Experimental Capabilities TLV

   The defining text for code point assignment for TLVs of the OSPF
   Router Information LSA says ([RFC4970]):

      o  1-32767 Standards Action.



Papdimitriou                  Experimental                     [Page 23]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


      o  Types in the range 32768-32777 are for experimental use; these
         will not be registered with IANA and MUST NOT be mentioned by
         RFCs.

      o  Types in the range 32778-65535 are reserved and are not to be
         assigned at this time.  Before any assignments can be made in
         this range, there MUST be a Standards Track RFC that specifies
         IANA Considerations that covers the range being assigned.

   That means that the new TLVs must be assigned type values from the
   range 32768-32777.  It is a matter for experimental implementations
   to assign their own code points, and to agree with cooperating
   implementations participating in the same experiments what values to
   use.

10.  References

10.1.  Normative References

   [RFC2119]    Bradner, S., "Key words for use in RFCs to Indicate
                Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2154]    Murphy, S., Badger, M., and B. Wellington, "OSPF with
                Digital Signatures", RFC 2154, June 1997.

   [RFC2328]    Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998.

   [RFC3630]    Katz, D., Kompella, K., and D. Yeung, "Traffic
                Engineering (TE) Extensions to OSPF Version 2", RFC
                3630, September 2003.

   [RFC3945]    Mannie, E., Ed., "Generalized Multi-Protocol Label
                Switching (GMPLS) Architecture", RFC 3945, October 2004.

   [RFC4202]    Kompella, K., Ed., and Y. Rekhter, Ed., "Routing
                Extensions in Support of Generalized Multi-Protocol
                Label Switching (GMPLS)", RFC 4202, October 2005.

   [RFC4203]    Kompella, K., Ed., and Y. Rekhter, Ed., "OSPF Extensions
                in Support of Generalized Multi-Protocol Label Switching
                (GMPLS)", RFC 4203, October 2005.

   [RFC4970]    Lindem, A., Ed., Shen, N., Vasseur, JP., Aggarwal, R.,
                and S. Shaffer, "Extensions to OSPF for Advertising
                Optional Router Capabilities", RFC 4970, July 2007.






Papdimitriou                  Experimental                     [Page 24]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   [RFC5226]    Narten, T. and H. Alvestrand, "Guidelines for Writing an
                IANA Considerations Section in RFCs", BCP 26, RFC 5226,
                May 2008.

   [RFC5250]    Berger, L., Bryskin, I., Zinin, A., and R. Coltun, "The
                OSPF Opaque LSA Option", RFC 5250, July 2008.

   [RFC5340]    Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF
                for IPv6", RFC 5340, July 2008.

   [RFC5786]    Aggarwal, R. and K. Kompella, "Advertising a Router's
                Local Addresses in OSPF TE Extensions", RFC 5786, March
                2010.

10.2.  Informative References

   [RFC4258]    Brungard, D., Ed., "Requirements for Generalized Multi-
                Protocol Label Switching (GMPLS) Routing for the
                Automatically Switched Optical Network (ASON)", RFC
                4258, November 2005.

   [RFC4652]    Papadimitriou, D., Ed., Ong, L., Sadler, J., Shew, S.,
                and D. Ward, "Evaluation of Existing Routing Protocols
                against Automatic Switched Optical Network (ASON)
                Routing Requirements", RFC 4652, October 2006.

   [RFC5073]    Vasseur, J., Ed., and J. Le Roux, Ed., "IGP Routing
                Protocol Extensions for Discovery of Traffic Engineering
                Node Capabilities", RFC 5073, December 2007.

   [RFC5709]    Bhatia, M., Manral, V., Fanto, M., White, R., Barnes,
                M., Li, T., and R. Atkinson, "OSPFv2 HMAC-SHA
                Cryptographic Authentication", RFC 5709, October 2009.

   For information on the availability of ITU Documents, please see
   http://www.itu.int.

   [G.7715]     ITU-T Rec. G.7715/Y.1306, "Architecture and Requirements
                for the Automatically Switched Optical Network (ASON)",
                June 2002.

   [G.7715.1]   ITU-T Draft Rec. G.7715.1/Y.1706.1, "ASON Routing
                Architecture and Requirements for Link State Protocols",
                November 2003.

   [G.805]      ITU-T Rec. G.805, "Generic functional architecture of
                transport networks)", March 2000.




Papdimitriou                  Experimental                     [Page 25]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   [G.8080]     ITU-T Rec. G.8080/Y.1304, "Architecture for the
                Automatically Switched Optical Network (ASON)," November
                2001 (and Revision, January 2003).

11.  Acknowledgements

   The author would like to thank Dean Cheng, Acee Lindem, Pandian
   Vijay, Alan Davey, Adrian Farrel, Deborah Brungard, and Ben Campbell
   for their useful comments and suggestions.

   Lisa Dusseault and Jari Arkko provided useful comments during IESG
   review.

   Question 14 of Study Group 15 of the ITU-T provided useful and
   constructive input.




































Papdimitriou                  Experimental                     [Page 26]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


Appendix A.  ASON Terminology

   This document makes use of the following terms:

   Administrative domain: (See Recommendation [G.805].)  For the
      purposes of [G7715.1], an administrative domain represents the
      extent of resources that belong to a single player such as a
      network operator, a service provider, or an end-user.
      Administrative domains of different players do not overlap amongst
      themselves.

   Control plane: performs the call control and connection control
      functions.  Through signaling, the control plane sets up and
      releases connections, and may restore a connection in case of a
      failure.

   (Control) Domain: represents a collection of (control) entities that
      are grouped for a particular purpose.  The control plane is
      subdivided into domains matching administrative domains.  Within
      an administrative domain, further subdivisions of the control
      plane are recursively applied.  A routing control domain is an
      abstract entity that hides the details of the RC distribution.

   External NNI (E-NNI): interfaces are located between protocol
      controllers between control domains.

   Internal NNI (I-NNI): interfaces are located between protocol
      controllers within control domains.

   Link: (See Recommendation G.805.)  A "topological component" that
      describes a fixed relationship between a "subnetwork" or "access
      group" and another "subnetwork" or "access group".  Links are not
      limited to being provided by a single server trail.

   Management plane: performs management functions for the transport
      plane, the control plane, and the system as a whole.  It also
      provides coordination between all the planes.  The following
      management functional areas are performed in the management plane:
      performance, fault, configuration, accounting, and security
      management.

   Management domain: (See Recommendation G.805.)  A management domain
      defines a collection of managed objects that are grouped to meet
      organizational requirements according to geography, technology,
      policy, or other structure, and for a number of functional areas
      such as configuration, security, (FCAPS), for the purpose of
      providing control in a consistent manner.  Management domains can
      be disjoint, contained, or overlapping.  As such, the resources



Papdimitriou                  Experimental                     [Page 27]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


      within an administrative domain can be distributed into several
      possible overlapping management domains.  The same resource can
      therefore belong to several management domains simultaneously, but
      a management domain shall not cross the border of an
      administrative domain.

   Subnetwork Point (SNP): The SNP is a control plane abstraction that
      represents an actual or potential transport plane resource.  SNPs
      (in different subnetwork partitions) may represent the same
      transport resource.  A one-to-one correspondence should not be
      assumed.

   Subnetwork Point Pool (SNPP): A set of SNPs that are grouped together
      for the purposes of routing.

   Termination Connection Point (TCP): A TCP represents the output of a
      Trail Termination function or the input to a Trail Termination
      Sink function.

   Transport plane: provides bidirectional or unidirectional transfer of
      user information, from one location to another.  It can also
      provide transfer of some control and network management
      information.  The transport plane is layered; it is equivalent to
      the Transport Network defined in Recommendation G.805.

   User Network Interface (UNI): interfaces are located between protocol
      controllers between a user and a control domain.  Note: There is
      no routing function associated with a UNI reference point.

Appendix B.  ASON Routing Terminology

   This document makes use of the following terms:

   Routing Area (RA): an RA represents a partition of the data plane,
      and its identifier is used within the control plane as the
      representation of this partition.  Per [G.8080], an RA is defined
      by a set of sub-networks, the links that interconnect them, and
      the interfaces representing the ends of the links exiting that RA.
      An RA may contain smaller RAs inter-connected by links.  The limit
      of subdivision results in an RA that contains two sub-networks
      interconnected by a single link.

   Routing Database (RDB): a repository for the local topology, network
      topology, reachability, and other routing information that is
      updated as part of the routing information exchange and may
      additionally contain information that is configured.  The RDB may
      contain routing information for more than one routing area (RA).




Papdimitriou                  Experimental                     [Page 28]


RFC 5787            ASON Routing for OSPFv2 Protocols         March 2010


   Routing Components: ASON routing architecture functions.  These
      functions can be classified as protocol independent (Link Resource
      Manager or LRM, Routing Controller or RC) or protocol specific
      (Protocol Controller or PC).

   Routing Controller (RC): handles (abstract) information needed for
      routing and the routing information exchange with peering RCs by
      operating on the RDB.  The RC has access to a view of the RDB.
      The RC is protocol independent.

   Note: Since the RDB may contain routing information pertaining to
      multiple RAs (and possibly to multiple layer networks), the RCs
      accessing the RDB may share the routing information.

   Link Resource Manager (LRM): supplies all the relevant component and
      TE link information to the RC.  It informs the RC about any state
      changes of the link resources it controls.

   Protocol Controller (PC): handles protocol-specific message exchanges
      according to the reference point over which the information is
      exchanged (e.g., E-NNI, I-NNI), and internal exchanges with the
      RC.  The PC function is protocol dependent.

Author's Address

   Dimitri Papadimitriou
   Alcatel-Lucent Bell
   Copernicuslaan 50
   B-2018 Antwerpen
   Belgium
   Phone: +32 3 2408491
   EMail: dimitri.papadimitriou@alcatel-lucent.be



















Papdimitriou                  Experimental                     [Page 29]